Re: Software program not loading

I think that I know what I am going to be doing this weekend.......

I'll keep you posted on progress. As always, your help is much appreciated.

Gordon



"Dave Patrick" <DSPatrick@xxxxxxxxxxxxxxxx> wrote in message news:#CjBvkorJHA.4324@xxxxxxxxxxxxxxxxxxxxxxx
If you can still boot Safe Mode I'd get any database (or other) backups before proceeding. Chances are good you're looking at doing a clean installation. Below is my standard boiler plate on this.

To do a clean install, either boot the Windows 2000 install CD-Rom or setup disks. The set of four install disks can be created from your Windows 2000 CD-Rom; change to the \bootdisk directory on the CD-Rom and execute makeboot.exe (from dos) or makebt32.exe (from 32 bit) and follow the prompts.

(Note: If your drive controller is not natively supported then you'll want to boot the Windows 2000 install CD-Rom. Then *F6* very early and very important (at setup is inspecting your system) in the setup to prevent drive controller detection, and select S to specify additional drivers. Then later you'll be prompted to insert the manufacturer supplied Windows 2000 driver for your drive controller in drive "A")

Setup inspects your computer's hardware configuration and then begins to install the Setup and driver files. When the Windows 2000 Professional screen appears, press ENTER to set up Windows 2000 Professional.

Read the license agreement, and then press the F8 key to accept the terms of the license agreement and continue the installation.

When the Windows 2000 Professional Setup screen appears, all the existing partitions and the unpartitioned spaces are listed for each physical hard disk. Use the ARROW keys to select the partitions Press D to delete an existing partition, If you press D to delete an existing partition, you must then press L (or press ENTER, and then press L if it is the System partition) to confirm that you want to delete the partition. Repeat this step for each of the existing partitions When all the partitions are deleted press F3 to exit setup, (to avoid unexpected drive letter assignments with your new install) then restart the pc then when you get to this point in setup again select the unpartitioned space, and then press C to create a new partition and specify the size (if required). Windows will by default use all available space.

Be sure to apply SP4 and these two below to your new install before connecting to any network. Internet included. (sasser, msblast)
http://download.microsoft.com/download/E/6/A/E6A04295-D2A8-40D0-A0C5-241BFECD095E/W2KSP4_EN.EXE
http://www.microsoft.com/technet/security/bulletin/MS03-043.mspx
http://www.microsoft.com/technet/security/bulletin/MS03-049.mspx


Then

Rollup 1 for Microsoft Windows 2000 Service Pack 4
http://www.microsoft.com/downloads/details.aspx?amp;displaylang=en&familyid=B54730CF-8850-4531-B52B-BF28B324C662&displaylang=en
and
http://www.microsoft.com/technet/security/bulletin/MS08-067.mspx



--

Regards,

Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft Certified Professional
Microsoft MVP [Windows]
http://www.microsoft.com/protect


"Gordon Biggar" wrote:
Hmmmmm......... I checked the diagnostic boot mode in msconfig and restarted, using first a normal boot and then a Last Known Good Configuration boot. Ran into the STOP error in both cases. Then tried the SAFE route. Got past the login screen, but then we went to an all black screen with "Safe Mode" in each of the corners. Stopped there for at least a couple of minutes, and then proceeded to the desktop. No diagnostic messages were encountered along the way, however.

I guess I will try the clean boot route next.

GB

.

Relevant Pages

  • Re: windows 2000 installation woes
    ... To do a clean install, either boot the Windows 2000 install CD-Rom or setup ... existing partition, If you press D to delete an existing partition, you must ...
    (microsoft.public.win2000.setup)
  • Re: XP reinstall - cannot delete c partition
    ... To do a clean install, boot the Windows XP install CD-Rom. ... Setup inspects your computer's hardware configuration and then begins to install the setup and driver files. ... When the Windows XP Professional screen appears, press ENTER to set up Windows XP Professional. ... Use the ARROW keys to select the partitions Press D to delete an existing partition, If you press D to delete an existing partition, you must then press L to confirm that you want to delete the partition. ...
    (microsoft.public.windowsxp.basics)
  • Re: Cant get Win2000 running
    ... To do a clean install, either boot the Windows 2000 install CD-Rom or setup ... existing partition, If you press D to delete an existing partition, you must ...
    (microsoft.public.win2000.general)
  • Re: how do you reboot with out disk?
    ... To do a clean install, boot the Windows XP install CD-Rom. ... Setup inspects your computer's hardware configuration and then begins to install the setup and driver files. ... When the Windows XP Professional screen appears, press ENTER to set up Windows XP Professional. ... Use the ARROW keys to select the partitions Press D to delete an existing partition, If you press D to delete an existing partition, you must then press L to confirm that you want to delete the partition. ...
    (microsoft.public.windowsxp.general)
  • Re: new cpu/mobo/memory, old HD, Blue Death Screen when upgrade past SP2
    ... To do a clean install, either boot the Windows 2000 install CD-Rom or setup ... existing partition, If you press D to delete an existing partition, you must ...
    (microsoft.public.win2000.general)