Re: Dual Boot System Win 2K & Win XP

Tech-Archive recommends: Repair Windows Errors & Optimize Windows Performance

Yes. After installing SP3 (or later) you must apply the reghack.

http://support.microsoft.com/kb/305098



--

Regards,

Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft Certified Professional
Microsoft MVP [Windows]
http://www.microsoft.com/protect


"Genuene1" wrote:
I have a 64 bit AMD Sempron system that I was trying to make a dual boot
system according to the instruction posted on this site. The HD is 320 GB.
I booted with the 2K cd since this is the opsys that must go on first. At
first, t showed the harddrive as 305000 +/-. So I attempted to make 2
separate partitions one about 145000G and the other about 155000G. The box
which prompts you to specify how large, would only allow me to type 5
characters. So I specified 90000 and it formatted the drive with NTFS
showing 89998. 2k installed fine. So I updated to SP4 and other updates.
Rebooted and still no problems so I installed XP on the remaining partiton,
which showed about 215002 +/-. XP installed without complications and I
updated to SP3. When I rebooted and tried to go into 2K, it showed the logo
and then suddenly halted with blue screen and the message STOP .....invalid
format or unknown format. I rebooted twice and the same error. I went back
into XP and no problem. I rebooted with the 2K cd and looked at the
partitions. It showed 2 but both was listed as unformatted or damaged
partition and now only 139000B shows as the harddrivesize. I removed the 2K
CD and rebooted with XP and XP saw it was a 320GB drive and saw the
partitions correctly. I rebootrd with 2K again and the same error showed
in the partitions. Now here's the catch. I rebooted with the 2K cd and
now my HD shows as 130000K +/- . Although it shows, it will not format or
allow me to delete the partiton only create. After I create, it is stuck
in a loop of formating and then showing install but it will not install/ When
I boot with my XP cd, It shows my drive as 305000 and I can delete and create
partitions and format but when I doot wit the 2K CD, it will not recognize
the format. It shows both as unformatted or damage. Does Win 2K have a
drive limitation so that it will not see my 320 GB drive? I've tried this 5
times? Any suggestions?

.

Relevant Pages

  • Re: installing 2nd drive into DIM 9200
    ... installing 2nd drive into DIM 9200 ... I wonder if you need to format a NEW drive at all? ... Once you define the partitions, a quick format is all you ...
    (alt.sys.pc-clone.dell)
  • RE: installing 2nd drive into DIM 9200
    ... installing 2nd drive into DIM 9200 ... I wonder if you need to format a NEW drive at all? ... Once you define the partitions, a quick format is all you ...
    (alt.sys.pc-clone.dell)
  • recovering hard drive partition
    ... I made a mistake when installing xp on a wd 250gb drive. ... I divided it into 2 partitions and installed xp but lost about 19gb of capacity. ... and how do I format this partition which was not formatted? ...
    (alt.os.windows-xp)
  • Re: HD wont let OS install
    ... >> partitions are notoriously difficult to remove unless you know the ... Sure; a low-level format. ... > they became Hitachi drives, ... > installing it as Primary Master drive) ...
    (uk.comp.homebuilt)
  • Dual Boot System Win 2K & Win XP
    ... I have a 64 bit AMD Sempron system that I was trying to make a dual boot ... separate partitions one about 145000G and the other about 155000G. ... format or unknown format. ... I rebootrd with 2K again and the same error showed ...
    (microsoft.public.win2000.applications)