Re: Windows 2000 server, booting from mirror, boot.ini

....is there no one out there who holds the key to this?....

Phil_Certain wrote:

> Hi,
>
> Can anyone help is advising how I can boot from a mirrored drive?
>
> I have Windows 2000 server installed on a single disk. I have recently
> added an identical disk in order to set up a RAID 1 mirror.
>
> Disk 0 is connected to IDE channel 1 as Master
> Disk 1 is connected to IDE channel 2 as master (CDROM is slave on IDE
> channel 2)
>
> I followed the process of converting disk 0 to a dynamic disk and then
> connecting the second disk, disk 1. I then mirrored the volumes to the
> new drive. All went well and a small (6MB) 'partion' of unallocated
> space was created on the second disk during the mirroring process.
>
>
> I created a boot floppy (as described in ms kb article 119467) that
> contained the files:
>
> boot.ini
> ntldr
> ntdetect.com
>
>
> [boot loader]
> timeout=30
> default=multi(0)disk(0)rdisk(0)partition(1)\WINNT
> [operating systems]
> multi(0)disk(0)rdisk(0)partition(1)\WINNT="Microsoft Windows 2000
> Server" /fastdetect
>
>
> Following the mirroring, I added a line to boot.ini so that it now
> reads:
>
> [boot loader]
> timeout=30
> default=multi(0)disk(0)rdisk(0)partition(1)\WINNT
> [operating systems]
> multi(0)disk(0)rdisk(0)partition(1)\WINNT="Microsoft Windows 2000
> Server" /fastdetect
> multi(0)disk(0)rdisk(1)partition(1)\WINNT="Microsoft Windows 2000
> Server" /fastdetect
>
> (ref
> http://support.microsoft.com/kb/102873/EN-US/#XSLTH3189121121120121120120)
>
>
> With both disks connected, the system will boot from the floppy with
> the boot.ini as shown imediately above, but guess what?...with disk0
> disconnected, the system will not boot to Windows. During the boot
> process, the system detects that disk0 is missing, requests f1 to
> continue and then delivers the message:
>
> Windows 2000 could not be started because of a hardware problem.
> Could not read from selected boot disk.
>
>
> I tried the following variations ot the 'mirro' entry in the boot.ini,
> but it made no difference:
>
> multi(0)disk(1)rdisk(0)partition(1)\WINNT="Microsoft Windows 2000
> Server" /fastdetect
> and
> multi(0)disk(0)rdisk(1)partition(2)\WINNT="Microsoft Windows 2000
> Server" /fastdetect
>
> Have also changes disk jumpers to set drives to 'cable selct', but this
> alos makes no difference
>
>
> So, I must be doing domething wrong somewhere. I've found conflicting
> advice on this subject, can anybody help ?
>
> Should both drives be connected to the same IDE channel?
>
> Is there a trick related to creating a MBR on the mirror disk prior to
> the mirroring process? If so, how is this done reliably?
>
> Any help greatly appreciated.

.

Relevant Pages

  • Re: *** STOP: (0x0000007B,0XF85438D0,0XC000009C,0X00000000,0x00000
    ... To start the Recovery Console, start the computer from the Windows XP CD-Rom ... and fixmbr for limited disk repairs. ... | Dave I could not create a boot disk at home, but I had created one at work ...
    (microsoft.public.win2000.general)
  • Re: CHKDSK repeatedly runs.
    ... How do I change the registry so this doesn't keep happening? ... There are times when the disk checking utility needs to ... run before you boot into Windows. ... I have a two year old laptop running Windows XP. ...
    (microsoft.public.windowsxp.help_and_support)
  • Re: New HDD Installation
    ... while your installation is up and running use the Disk Management tool and make sure that you have a properly identified System Partition and that it is marked as "Active". ... If it is so identified and marked and still won't boot then do both commands as Ron suggested. ... Description of the Windows XP Recovery Console ... It would take awhile but I am willing to start fresh if it gets the new HDD in and the small out. ...
    (microsoft.public.windowsxp.general)
  • Re: Start Up Error Messages
    ... That hangs around for c 20 seconds and then the boot ... Go a head and remove and run disk clean up and see if the check disk will ... How To Schedule Tasks in Windows XP ... Under General Tab clear your History, ...
    (microsoft.public.windowsxp.basics)
  • Re: Moving beyond "Tutorial: Building and Deploying a Run-Time Ima
    ... try running TAP.exe under Windows 98 to ... missing a critical boot device, ... > I did partition/format the disk in the development PC using NTFS. ... drive while it was in the target PC and "it" works fine. ...
    (microsoft.public.windowsxp.embedded)