Re: Vista install loads BOOTSECT.BAK to second HDD

Andy that url was general questions for vista eeerm did you mean a different
page? or what was the heading for the info you suggest

"andy" wrote:

On Wed, 25 Jun 2008 16:50:01 -0700, jamesph
<jamesph@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote:

during install of Vista ultimate to new system with 2 x 750GB Sata HDD..I
partitioned 100GB of the first disk (0) to take the Vista system. Windows
asked where to put the installation and I highlighted the new partition but
then it indicated it needed space to put what I thought it said was the
System Volume?

This is a warning that the drive you're installing Vista on is not the
drive that the BIOS is set to boot from, meaning that the System
partition won't be placed on that drive.

and that there was enough space on the disk I thought
it meant partition 1 and highlighted that and clicked yes in the dialogue
window...after the install I saw that it had placed a file of 8kb namely
BOOTSECT.BAK onto the second HDD. In disk management disks show as c: Simple
Basic NTFS Healthy (Boot,Page File, Crash Dump, Primary partition) and the
second disk as D: simple Basic NTFS Healthy (System, Active,Primary
Partition)....Also Both disks show total storage as 698GB each ?

The reason the drives are only 698GB in Windows is because the GB that
Windows uses (1GB = 2^30 = 1,073,741,824 bytes) are larger than the GB
that drive manufacturers use (1GB = 10^9 = 1,000,000,000 bytes).

Whats going
on and can I do anything other than a new install ? If a new install is
needed (I havent activated vista yet) what should i do second time
around....thanks for any help

Windows setup places its System partition on the physical disk drive
that the BIOS is set to boot from. Go into BIOS setup and check the
setting of Hard Disk Boot Priority or Hard Disk Drives. The drive that
is at the top of the list of drives is the one that Windows setup is
supposed to put the boot manager files. Having two identical drives
can make it confusing as to which drive is which.

Go into BIOS setup and move the other 750GB disk drive to the top of
the drives list. Then you can reinstall.

Or first run Disk Management and mark the C: partition on the Vista
drive as Active. Then go into BIOS setup and move the other 750GB
drive to the top of the drives list. Then place Vista's boot manager
on the Vista drive by following steps 2 through 15 at
Ignore any references to Windows XP.



Relevant Pages

  • Re: Dual Boot Instructions
    ... the PHYSICAL DISK number, ... Partition and Boot Volume as well as other things. ... You should, at any one time, see ONE System Partition and ONE Boot Volume - ... for the typical two floppy drives and assigning Drive C: ...
  • Re: Boot Problem
    ... Right mouse click the dest disk> Advanced> Edit ... but it should eventually boot to Windows. ... I see a lot of posts in here about the ability of Acronis to clone drives. ... I have managed to successfully copy by DELETING partition, ...
  • Re: Dual Boot Instructions
    ... OS on a separate partition. ... the PHYSICAL DISK number, ... You should, at any one time, see ONE System Partition and ONE Boot ... The name stuck when we added hard disk drives, ...
  • Re: A Dual-boot question; I thought C was always the partition with the running OS
    ... The Server 2003 will then call its partion "C:" Local Disk. ... When Server 2003 starts up, it will call itself "C:" and it will call the WinXP partition "E:", but again, who cares? ... The OS then assigns drive letters to the first primary partition recognized on each successive hard disk. ... Because they're on separate hard drives, ...
  • Re: HDD speeds
    ... relatively small first partition with the OS crap (and, ... the highest sdtr part of the disk, the start of the disk space on the ... bespoke partition space will have much less impact than if they could ... Ecogreen drives make more sense for an always on NAS ...