Re: ruler settings
- From: "michiel" <niets@xxxxxxxx>
- Date: Thu, 14 Jul 2005 09:25:43 +0200
Well OK. Bad luck it can not be changed. At least it is a comfort to know
that I didn´t cause this behaviour of Visio.
Thank you ever so much.
"John Marshall, MVP" <lancucki@xxxxxxxxxxxxx> schreef in bericht
news:O2bz7Y6hFHA.1044@xxxxxxxxxxxxxxxxxxxxxxx
> Good question. In Visio, you can make a drawing as large as possible.
The
> outline of the page indicates if your drawing is within the the page
> boundaries. If you overlap the background area, that section of the
> drawing will not print.
>
> Using zoom, you should be able to control the amount of background space
> that is visible. When I work on drawings, I'm zoomed to 100% and rarely
> see enough of the page to see the edges.
>
> John... Visio MVP
>
> Need stencils or ideas? http://www.mvps.org/visio/3rdparty.htm
> Need VBA examples? http://www.mvps.org/visio/VBA.htm
> Common Visio Questions http://www.mvps.org/visio/common_questions.htm
> "michiel" <niets@xxxxxxxx> wrote in message
> news:42d4ea26$0$26408$e4fe514c@xxxxxxxxxxxxxxxxx
>> But then what is this large gap good for? I don´t use this, so why
would
>> it
>> show?
>>
>>
>>
>> "John Marshall, MVP" <lancucki@xxxxxxxxxxxxx> schreef in bericht
>> news:e7Q4A7vhFHA.3692@xxxxxxxxxxxxxxxxxxxxxxx
>>> Sounds like it is working normally. The page is centered in the
drawing
>>> area and the rulers are zeroed at the edges. You can zoom in to reduce
>> the
>>> amount of background that is visible.
>>>
>>>
>>> John... Visio MVP
>>>
>>> Need stencils or ideas? http://www.mvps.org/visio/3rdparty.htm
>>> Need VBA examples? http://www.mvps.org/visio/VBA.htm
>>> Common Visio Questions http://www.mvps.org/visio/common_questions.htm
>>> "michiel" <niets@xxxxxxxx> wrote in message
>>> news:42d3be31$0$22145$e4fe514c@xxxxxxxxxxxxxxxxx
>>>> Yes, vertical zero lines up with left bottom, and horizontal with
upper
>>>> left edge.
>>>> With that, there is a huge gap.
>>>>
>>>> Changing the zoom doesn´t help.
>>>> I tried dragging the page to the upper left corner again, bit it
didn´t
>>>> want to move.
>>>>
>>>>
>>>>
>>>> "John Marshall, MVP" <lancucki@xxxxxxxxxxxxx> schreef in bericht
>>>> news:%23ceIf$thFHA.1248@xxxxxxxxxxxxxxxxxxxxxxx
>>>>> Does the vertical zero line up with the bottom of the drawing and
the
>>>>> horizontal align with the left edge?
>>>>>
>>>>> What is the zoom setting?
>>>>>
>>>>> John... Visio MVP
>>>>>
>>>>> Need stencils or ideas? http://www.mvps.org/visio/3rdparty.htm
>>>>> Need VBA examples? http://www.mvps.org/visio/VBA.htm
>>>>> Common Visio Questions
http://www.mvps.org/visio/common_questions.htm
>>>>> "michiel" <niets@xxxxxxxx> wrote in message
>>>>> news:42d3b151$0$21654$e4fe514c@xxxxxxxxxxxxxxxxx
>>>>>> Can´t find out how to set the ruler for the drawing to show in the
>>>>>> upper
>>>>>> left corner.
>>>>>> My ruler starts in that upper left corner at -80 X and 520 Y, with
>> the
>>>>>> result that I have to find the drawing somewhere in the dungeons.
>>>>>> Can anyone tell me how to change this?
>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>>
>
>
.
- References:
- ruler settings
- From: michiel
- Re: ruler settings
- From: John Marshall, MVP
- Re: ruler settings
- From: michiel
- Re: ruler settings
- From: John Marshall, MVP
- Re: ruler settings
- From: michiel
- Re: ruler settings
- From: John Marshall, MVP
- ruler settings
- Prev by Date: Re: Visio addiction
- Next by Date: Reading LogicWorks ERWin 3.5 ERX files...
- Previous by thread: Re: ruler settings
- Next by thread: Horizontal Organization Chart
- Index(es):
Relevant Pages
|
