Re: Dell Axim X30 on NETGEAR W.Router MR814

From: Jason (rockjock2020_at_aol.com)
Date: 08/03/04 

Date: Mon, 2 Aug 2004 17:29:20 -0700

You can usually find the TX/RX settings on the performance page of your
router setup.

You can also check these sites out for help they helped me

http://www.cewindows.net/started.htm

http://wifi.aximsite.com/

"Edward Chan" <f22_r@hotmail.com> wrote in message
news:%23Ca545JeEHA.3664@TK2MSFTNGP12.phx.gbl...
> I don't think the router that I have has an option preamble.. My firmware
of
> the router is updated though. How can I check the TX/RX rates? Do you mean
> the TX/RX from the X30? If so, the rates are 1, 2, 5.5, and 11Mbps. I'm
not
> sure about anything running at 4x mode on my router because I don't know
> here to find it. Either my router settings are just difficult to read, or
> it's just bad. When I look in the router settings, I don't see anything
that
> shows 4x or 4 times.
>
> Thanks,
>
> "Jason" <rockjock2020@aol.com> wrote in message
> news:uG0uOe9dEHA.1356@TK2MSFTNGP09.phx.gbl...
> > There are a couple of things I had to do with my DLink router before I
> could
> > connect to it. I had the same problems that you are having.
> > Some are obvious and others aren't.
> > Firmware up to date? If it isn't go to the website www.netgear.com and
> > update it.
> > Turn your preamble to Short. I don't know why it makes a difference but
> > with mine it allowed me to connect faster to my router.
> > What are you TX/RX rates? I had to limit mine down to 11Mbs. Now don't
> get
> > excited about this one. Unless you are transfering large files over
your
> > network you'll never notice this change. Most Internet servers are only
> > running <3Mbs.
> > And here's the one that was killing me the most.
> > Do you have anything on your router that is a 4x mode? If you do turn
it
> > off.
> >
> > Hope this helps
> >
> > Jason
> >
> >
> > "Edward Chan" <f22_r@hotmail.com> wrote in message
> > news:uuuH1zydEHA.3916@TK2MSFTNGP11.phx.gbl...
> > > Hi,
> > >
> > > I got my Axim X30 624Mhz four days ago and I've been struggling to
find
> a
> > > way to allow it to connect to my wireless router (NETGEAR Wireless
> Router
> > > MR814).
> > >
> > > Here are the wireless settings I have on my Wireless Router:
> > >
> > > SSID: Enabled
> > > Regioin: Canada
> > > Channel: 01
> > >
> > > Broadcast of SSID OFF
> > > Access from 'any' name OFF
> > >
> > > Wireless Card Access List: I put my Axim X30 here along with it's MAC
> > > Address.
> > >
> > > WEP Authentication Type: Automatic
> > > Encryption Strength: 128-bit
> > >
> > > WEP Key: I made four keys here using 128-bit
> > >
> > > And here are the settings I put in my Axim X30's WLAN Utitlity: I
added
> a
> > > new wireless network with these settings:
> > >
> > > Network Name: <can't say here lol>
> > > Connects to: Work
> > >
> > > This device is not a device-to-device (ad-hoc) connection
> > >
> > > Authentication: Open (there is no option for Automatic like my
Wireless
> > > Router has)
> > > Data Encryption: WEP
> > >
> > > The key is not provided for me automatically.
> > >
> > > I put my network key for the 128-bit 26 character from the router's
Key
> > > index #1 into my PDA
> > > Key Index selected is 1.
> > >
> > > And I disabled the 802.1x option.
> > >
> > > ----------------------
> > >
> > > Now the conclusion is when I view the connection, it says that the
> > > connection is Excellect and is connected. The problem is when I try to
> use
> > > the Internet via PIE (Pocket Internet Explorer), it says that I'm not
> > > connected to the network...
> > >
> > > What should I do to allow my PDA/PPC to access my network wirelessly?
> > >
> > > Thanks,
> > > - Ed
> > >
> > >
> >
> >
>
>

Relevant Pages

  • Re: WPA from PocketPC
    ... Use WPA with a LONG RANDOM key, larger than 20 characters in length... ... > I assume that "Network Name" on the PDA is the same thing as "ESSID" on the ... > The router makes no mention of "TKIP," but since you are both using that, ... > server provides DNS settings, I shouldn't have to change the PDA from its ...
    (microsoft.public.pocketpc)
  • Re: What router extra question
    ... faulty & not any of the various other things probs like that can ... that could mean any one of several things were causing the prob! ... It may be a faulty Router, or it could be a faulty Power ... whenever needed & then just bung the Settings ...
    (uk.people.silversurfers)
  • RE: Internet explorer does not connect
    ... What your Firewall settings? ... Did you powered the Router Down and the Computer for about 2 minutes then ... Click on Internet WAN, then on Connection Type: ... later for this step to copy the error message on it. ...
    (microsoft.public.windowsxp.help_and_support)
  • Re: Networking over mains cables
    ... Graeme Wall wrote: ... one in the Billion router and one in the Mac G4. ... of the box settings should be fine. ... APPLICATIONS access the internet. ...
    (comp.sys.acorn.networking)
  • Re: What router extra question
    ... OK no lights was to me a sort of giveaway that it was the power supply :-) ... Have you checked that the "spare" Power ... The Settings are stored in CMOS (or some other sort of NVR ... a prob with the Router, one of the things to do is to do ...
    (uk.people.silversurfers)