Re: I want to use MailMarshal as edge

The following post from another forum fixed my problem but I have a question:
All of the directions I have read did not include this information. Since I
had a pretty simple implementation of adding and Exchange 2007 server to my
Exchange 2003 organization, I would guess that others have to do the same?
Just a thought.

"On your Exchange 2003 server, can you check the properties of the SMTP
virtual server? Under the "Access" tab and then "Authentication" is
"Integrated Windows Authentication" checked?"

I had anonymous checked but not Integrated Windows. Did that and now all is
well.
Thanks to both of you for your help.




"Leif Pedersen [ MVP]" wrote:

Hi,

You configured the send connector to send through an exchange server (with
authentication)?

Remove authentication from the send connector and you should be fine.

Leif

"pepe" <pepe@xxxxxxxxxxxxxxxxxxxxxxxxx> skrev i meddelelsen
news:B317504D-497B-4EAD-B266-4139BEA01FC6@xxxxxxxxxxxxxxxx
Thank you for your response:
1. Send connector is forwarding to both dns name and ip of smarthost. I
can
ping both the dns name and ip of smarthost
2. Mail marshall allows relaying by ip address and range. It is set to
allow
both exchange servers.
3. Yes, server can resolve fqdn as far as i can tell
4. Yes, i can telnet to smarthost on port 25
5. Send connector is enabled
6. Where are smtp logs?
7. application log shows nothing of interest as far as i can tell

In the queue viewer, i see in the "Last Error"

451 4.4.0 Primary target IP address responded with: "451 5.7.3 Cannot
achieve Exchange Server Authentication. "Attempted failover to alternate
host, but that did not succeed. Either there are no alternate hosts, or
delivery failed to all alternate hosts.

Anything else i can check?

thanks again


"Bharat Suneja [MVP]" wrote:

- Send Connector for address space * - is it set to forward to the right
smarthost IP address/fqdn?
- Are the authentication settings correct? (if the server needs to
authenticate with the smarthost)
- Can the server resolve the fqdn of the smarthost (if fqdn is used in
Connector settings)
- Does the server have SMTP connectivity to smarthost (telnet on smtp
port)?
- Is the Send Connector enabled?
- Anything in the SMTP protocol logs?
- Anything in Application event log?
--
Bharat Suneja
MVP - Exchange
www.zenprise.com
NEW blog location:
exchangepedia.com/blog
--------------------------


"pepe" <pepe@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:C3F2A840-5550-490F-B7B2-CB911FF62533@xxxxxxxxxxxxxxxx
I have one Ex2003 Server and just installed an Ex2007 with
hub/mail/client
role. We currently forward all of our mail to a dmz machine with
MailMarshall
(antivirus,spam, etc). Test mailboxes on the Ex07 can receive mail
fine,
but
cannot send. I can see them in the queue viewer but aren't being
delivered.
After several hours, the mailbox receives a "delivery delayed" message.

Where should I look to fix this?

Thanks for your help.



.

Relevant Pages

  • Re: Exchange 2007 Send Connector problem with Internal email address
    ... I am trying to send email from ..NET application, and I can embed user authentication in the app. ... The SMTP server requires a secure connection or the client was not authenticated. ... setup a Receive Connector with appropriate permissions. ... I can send email out of all internet email addresses with the send connector ...
    (microsoft.public.exchange.setup)
  • Re: Reason for mail sending fails ???
    ... There was a SMTP communication problem with the recipient's email server. ... discover your ISP's mail server IP and use that as the smarthost. ... >> WHat I have verify if the config of my SMTP connector and as I did not ...
    (microsoft.public.windows.server.sbs)
  • Re: Reason for mail sending fails ???
    ... There was a SMTP communication problem with the recipient's email server. ... discover your ISP's mail server IP and use that as the smarthost. ... WHat I have verify if the config of my SMTP connector and as I did not ...
    (microsoft.public.windows.server.sbs)
  • Re: Reason for mail sending fails ???
    ... I guess even its along time you have not setup a sbs I think we are nealr ... WHat I have verify if the config of my SMTP connector and as I did not ... tries to contact the email server at that domain to deliver the ... The second is to use a "smarthost". ...
    (microsoft.public.windows.server.sbs)
  • Re: Setup of
    ... For Authentication, it has nothing checked. ... Exchange Server authentication ... Whatever I set under Unixmail receive connector will not do ...
    (microsoft.public.exchange.setup)