Re: I want to use MailMarshal as edge

Hi,

You configured the send connector to send through an exchange server (with authentication)?

Remove authentication from the send connector and you should be fine.

Leif

"pepe" <pepe@xxxxxxxxxxxxxxxxxxxxxxxxx> skrev i meddelelsen news:B317504D-497B-4EAD-B266-4139BEA01FC6@xxxxxxxxxxxxxxxx
Thank you for your response:
1. Send connector is forwarding to both dns name and ip of smarthost. I can
ping both the dns name and ip of smarthost
2. Mail marshall allows relaying by ip address and range. It is set to allow
both exchange servers.
3. Yes, server can resolve fqdn as far as i can tell
4. Yes, i can telnet to smarthost on port 25
5. Send connector is enabled
6. Where are smtp logs?
7. application log shows nothing of interest as far as i can tell

In the queue viewer, i see in the "Last Error"

451 4.4.0 Primary target IP address responded with: "451 5.7.3 Cannot
achieve Exchange Server Authentication. "Attempted failover to alternate
host, but that did not succeed. Either there are no alternate hosts, or
delivery failed to all alternate hosts.

Anything else i can check?

thanks again


"Bharat Suneja [MVP]" wrote:

- Send Connector for address space * - is it set to forward to the right
smarthost IP address/fqdn?
- Are the authentication settings correct? (if the server needs to
authenticate with the smarthost)
- Can the server resolve the fqdn of the smarthost (if fqdn is used in
Connector settings)
- Does the server have SMTP connectivity to smarthost (telnet on smtp port)?
- Is the Send Connector enabled?
- Anything in the SMTP protocol logs?
- Anything in Application event log?
--
Bharat Suneja
MVP - Exchange
www.zenprise.com
NEW blog location:
exchangepedia.com/blog
--------------------------


"pepe" <pepe@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:C3F2A840-5550-490F-B7B2-CB911FF62533@xxxxxxxxxxxxxxxx
>I have one Ex2003 Server and just installed an Ex2007 with >hub/mail/client
> role. We currently forward all of our mail to a dmz machine with
> MailMarshall
> (antivirus,spam, etc). Test mailboxes on the Ex07 can receive mail > fine,
> but
> cannot send. I can see them in the queue viewer but aren't being
> delivered.
> After several hours, the mailbox receives a "delivery delayed" message.
>
> Where should I look to fix this?
>
> Thanks for your help.



.

Relevant Pages

  • Re: Exchange 2007 Send Connector problem with Internal email address
    ... I am trying to send email from ..NET application, and I can embed user authentication in the app. ... The SMTP server requires a secure connection or the client was not authenticated. ... setup a Receive Connector with appropriate permissions. ... I can send email out of all internet email addresses with the send connector ...
    (microsoft.public.exchange.setup)
  • Re: WM5 can not sync to exchange
    ... On the SBS 2003 Server open the Server Management console. ... Please verify Authentication settings by the following steps. ... Open IIS Manager ... Collect the IIS metabase on Exchange Server and send to me: ...
    (microsoft.public.windows.server.sbs)
  • [NT] Vulnerability in Exchange Server 2003 Could Lead to Privilege Escalation (MS04-002)
    ... Access on Windows 2000 and Windows Server 2003, ... back-end Exchange 2003 servers that are running Windows Server 2003. ... Kerberos authentication is used as the HTTP authentication ... Windows Server 2003 server that also functions as an Exchange Server 2003 ...
    (Securiteam)
  • Re: Problems sending email in SBS 2008
    ... The default connector has the following ticks on the Authentication ... Ticked - Exchange Server Authentication ...
    (microsoft.public.windows.server.sbs)
  • Re: Problems sending email in SBS 2008
    ... I should change on the default connector? ... The default connector has the following ticks on the Authentication ... Ticked - Exchange Server Authentication ...
    (microsoft.public.windows.server.sbs)