Re: Help in accessing GPIOs in an i.MX21 (ADS21 board)

Hi Paul,

The size of enumeration is 32-bits. I built a simple unmanaged
application and used sizeof on the enumration and it returned a value
of 4. By declaring the parameters to be Int32 and passing values of
0x000002 or 0x000003, I still see at the driver side that it sees
Port_A, which is 0x00000000. Is there a layer between my managed
application and the driver that I can snoop and see what actually was
passed? Thanks all for all your responses.

mario


Paul G. Tobey [eMVP] wrote:
OK, so forget about trying to P/Invoke with a managed enumeration. Declare
the parameter as an Int32 and pass the value that corresponds to some other
port (1, 2, 3, whatever), and see what you get in that case. It would be
useful to verify the size of the enumeration expected by the unmanaged code,
also. I would expect it to be 32-bit, but I could be wrong about that.

Paul T.

"Mario" <alphatommy@xxxxxxxxxxx> wrote in message
news:1158870731.936903.11560@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Hi Paul,

Sorry, what I meant by "did not work" was that regardless of what value
I sent as Port (GPIO_PORT_B, C, D, E or MAX) I still see that the value
passed for Port is GPIO_PORT_A. I see this by breaking on the driver,
and GPIO_PORT_A is the value that shows up when I place the cursor on
top of Port or through Quick Watch. The value that is returned is
wrong because it is looking at the different port that I have selected.
I still have to try to call the method from an umanaged application.
Thanks.

-- mario

Paul G. Tobey [eMVP] wrote:
Sorry, "did not work" is useless information. What value did you pass?
What was returned in the byte? What do you get when you pass the same
values from unmanaged code?

Paul T.

"Mario" <alphatommy@xxxxxxxxxxx> wrote in message
news:1158794169.432339.250470@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Hi Paul,

I could try using byte for return value. On the GPIO_PORT, I have
tried Int32 before, but it did not work. Thanks.

-- mario


Paul G. Tobey [eMVP] wrote:
Well, that return type is wrong. Clearly you should be returning some
8-bit
value, which you aren't. Try 'byte'; it's a good choice.

Try also, for now, just making the GPIO_PORT parameter an Int32 and
passing
the right value as an integer to it. Does that work?

Paul T.


"Mario" <alphatommy@xxxxxxxxxxx> wrote in message
news:1158791251.466377.92460@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Hi Paul,

For the method INT8 DDKGetGpioSignalState(GPIOHANDLE gpiohandle,
GPIO_PORT port, UINT32 signal)

I did the following:

[DllImport ("mx21ddk.dll")] //mx21ddk.dll contains the methods
that
I am calling
public static extern Int16 DDKGetGpioSignalState(IntPtr gpiohandle,
GPIO_PORT port, UInt32 signal);

The reason why I used Int16 is because there is no Int16 in C#.

//GPIO in C#
public enum
{
GPIO_PORT_A,
GPIO_PORT_B,
GPIO_PORT_C,
GPIO_PORT_D,
GPIO_PORT_E,
GPIO_PORT_F,
GPIOPORTMAX
}

Please let me know if you see any errors. Thanks.

mario


Paul G. Tobey [eMVP] wrote:
Those don't appear to be standard DDK calls to me, but I'm no
expert
on
any
i.MX21 BSPs. How have you P/Invoked them? GPIOHANDLE is probably
an
IntPtr, GPIO_PORT you can probably create an enum for that
corresponds
directly to what the C/C++ code uses, UINT32 is pretty obvious,
'uint',
etc.
What value, integer value, are you passing in the GPIO_PORT
parameters?

Paul T.

"Mario" <alphatommy@xxxxxxxxxxx> wrote in message
news:1158785258.148715.111740@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Hi Paul,

I have tried the following methods (their signatures are as
follow):

1. INT8 DDKGetGpioSignalState(GPIOHANDLE gpiohandle, GPIO_PORT
port,
UINT32 signal)
2. void DDKSetGpioSignalState(GPIOHANDLE gpiohandle, GPIO_PORT
port,
UINT32 signal, UINT8 state, BOOL bInPowerMode)

3. UINT32 DDKGetGpioSignals(GPIOHANDLE gpiohandle, GPIO_PORT
port,
UINT32 signalMask)

4. void DDKSetGpioSignals(GPIOHANDLE gpiohandle, GPIO_PORT
port,
UINT32 signalMask, UINT32 stateMask)

GPIO_PORT is defined in the driver header as:

typedef enum {
GPIO_PORT_A,
GPIO_PORT_B,
GPIO_PORT_C,
GPIO_PORT_D,
GPIO_PORT_E,
GPIO_PORT_F,
GPIO_PORT_MAX,
} GPIO_PORT;

Thanks in advance for any input.

-- mario


Paul G. Tobey [eMVP] wrote:
What GPIO method calls?

Paul T.

"Mario" <alphatommy@xxxxxxxxxxx> wrote in message
news:1158076582.805617.137440@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Hi,

Has anyone had any success in accessing (reading and writing)
the
GPIOs
in a Freescale i.MX21 (ADS21 board) from a managed code
application?
The problem that I have is that regardless of which port
parameter I
pass in the GPIO method calls, the GPIO driver always take
Port_A
as
default. The rest of the parameters are passed correctly.
Any
inputs
or suggestions on how to fix this is appreciated. Thanks.

I am not sure if this is the correct forum, but I did not get
any
response after posting the same question in the freescale site
for
almost two weeks.


-- mario






.

Relevant Pages

  • Re: Help in accessing GPIOs in an i.MX21 (ADS21 board)
    ... how is GPIOHANDLE declared by the unmanaged code? ... Paul G. Tobey wrote: ... I sent as Port I still see that the value ... UINT32 signalMask, UINT32 stateMask) ...
    (microsoft.public.dotnet.framework.compactframework)
  • Re: Help in accessing GPIOs in an i.MX21 (ADS21 board)
    ... I sent as Port I still see that the value ... Paul G. Tobey wrote: ... For the method INT8 DDKGetGpioSignalState(GPIOHANDLE gpiohandle, ... UINT32 signalMask, UINT32 stateMask) ...
    (microsoft.public.dotnet.framework.compactframework)
  • Re: Help in accessing GPIOs in an i.MX21 (ADS21 board)
    ... Paul G. Tobey wrote: ... For the method INT8 DDKGetGpioSignalState(GPIOHANDLE gpiohandle, ... GPIO_PORT port, UINT32 signal) ... UINT32 signalMask, UINT32 stateMask) ...
    (microsoft.public.dotnet.framework.compactframework)
  • Re: Help in accessing GPIOs in an i.MX21 (ADS21 board)
    ... Paul G. Tobey wrote: ... For the method INT8 DDKGetGpioSignalState(GPIOHANDLE gpiohandle, ... GPIO_PORT port, UINT32 signal) ... UINT32 signalMask, UINT32 stateMask) ...
    (microsoft.public.dotnet.framework.compactframework)
  • Re: Help in accessing GPIOs in an i.MX21 (ADS21 board)
    ... GPIOHANDLE is declared in the unmanaged code as typedef ... Paul G. Tobey wrote: ... I sent as Port I still see that the value ... UINT32 signalMask, UINT32 stateMask) ...
    (microsoft.public.dotnet.framework.compactframework)