Re: sdram configuration,pls help
- From: "Maxim S. Shatskih" <maxim@xxxxxxxxxxxxxxxx>
- Date: Sat, 3 May 2008 17:53:41 +0400
Ask on microsoft.public.windowsce.platbuilder
--
Maxim Shatskih, Windows DDK MVP
StorageCraft Corporation
maxim@xxxxxxxxxxxxxxxx
http://www.storagecraft.com
"blueYork" <yaoronger@xxxxxxx> wrote in message
news:4894b8b6-07cf-4e81-a68d-b7937d8555a2@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
dear all,
I know this might be an old question for u guys,
but I really met some troubles within it.
My platform is:
CPU : Xscale pxa255
OS : Windows CE .Net 4.2
Flash : 32MB
SDRAM : 128MB (32MBX4)
Now I want to set the configuration of 128M SDRAM.
following some suggestions,I modified the some files below,
but it does not work..
now,I list my main modification:
//////////////////////////////////////
config.bib
//////////////////////////////////////
MEMORY
IF IMGFLASH !
NK 800B8000 02000000 RAMIMAGE
RAM 820B8000 05C00000 RAM
EDBG 87F8D000 00020000 RESERVED
ENDIF
AUD_DMA 87CB8000 0000A000 RESERVED
SLEEP_SAV 87CC2000 00001000 RESERVED
DRV_GLB 87CC3000 00001000 RESERVED
CACHE_FLG 87CC4000 0003C000 RESERVED
DISPLAY 87D00000 00130000 RESERVED
BLOCK_BUF 87E30000 00080000 RESERVED
UNUSED_BUF 87EB0000 000DD000 RESERVED
whql_sig 00000001 00002000 EXTENSION
ZBANK 88000000 00100000 RESERVED
CONFIG
IF IMGFLASH !
AUTOSIZE=ON
ENDIF
IF IMGFLASH !
ROMSTART=800B8000
ROMWIDTH=32
ENDIF
ROMSIZE=01D00000
/////////////////////////////////
memmap.inc
////////////////////////////////
DCD SDRAM_BASE_C_VIRTUAL,SDRAM_BASE_PHYSICAL,128
DCD ZBANK_BASE_C_VIRTUAL, ZBANK_BASE_PHYSICAL, 1 DCD
MEMC_BASE_C_VIRTUAL, MEMC_BASE_PHYSICAL, 1 DCD
PERIF_BASE_C_VIRTUAL, PERIF_BASE_PHYSICAL,32 DCD
PCMCIA_S0_IO_C_VIRTUAL, PCMCIA_S0_IO_PHYSICAL, 32 DCD
PCMCIA_S0_ATTR_C_VIRTUAL, PCMCIA_S0_ATTR_PHYSICAL, 32
DCD PCMCIA_S0_CMN_C_VIRTUAL, PCMCIA_S0_CMN_PHYSICAL,
64
DCD PCMCIA_S1_IO_C_VIRTUAL, PCMCIA_S1_IO_PHYSICAL,32
DCD PCMCIA_S1_ATTR_C_VIRTUAL, PCMCIA_S1_ATTR_PHYSICAL,
32
DCD PCMCIA_S1_CMN_C_VIRTUAL, PCMCIA_S1_CMN_PHYSICAL,
64
DCD LCD_BASE_C_VIRTUAL,
LCD_BASE_PHYSICAL, 1
DCD BOOT_FLASH_BASE_C_VIRTUAL, BOOT_FLASH_BASE_PHYSICAL,
32
DCD CS8900A_BASE_C_VIRTUAL, CS8900A_BASE_PHYSICAL,
1
DCD XHYPER255B_PERI_C_VIRTUAL, XHYPER255B_PERI_PHYSICAL, 5
DCD CY7C67300_BASE_C_VIRTUAL,
CY7C67300_BASE_PHYSICAL, 1
DCD nCS4_BASE_C_VIRTUAL,
nCS4_BASE_PHYSICAL, 8
DCD nCS5_BASE_C_VIRTUAL,
nCS5_BASE_PHYSICAL, 8
DCD 0x00000000, 0x00000000, 0
then,I changed xsc1.h,xsc1.inc,xsc1bd.h,xsc1bd.inc to
be in sync with config.bib and OEMAddressTable,
and I checked a lot ,there's no problem with them.
///////////////////////////////////////////////////////////////////////
and in memdefs.h, I was a little confused about the codes below:
and I modified the two values which I marked to sync.
///////////////////////////////////////////////
#ifndef SABINAL
//
// Cotulla-32 Defs
//
#define MEM_BASE_PHYSICAL 0xA3CB8000
#define MEM_BASE_C_VIRTUAL 0x87CB8000 //modifed
#define EDBG_PHYSICAL_MEMORY_START 0x87F8D000 //modifed
#else
//
// Sabinal Defs
//this seems not used,so I do not modify the value
#define MEM_BASE_PHYSICAL 0xA1CB8000
#define MEM_BASE_C_VIRTUAL 0x81CB8000
#define EDBG_PHYSICAL_MEMORY_START 0x81F8D000
#endif
///////////////////////////////////////////
I also changed the value in xsc1bd.inc
MDCNFG_VAL EQU 0x19C319C3
; Setup default MDCNFG value for 128MB SDRAM
///////////////////////////////////////////
in the end,according to K.S.huang's advice,i modified file fwxsc1.s
; enable sdram bank 0 if installed (must do for any populated bank)
orr r3, r3, #MDCNFG_DE0
;4.28 add
orr r3, r3, #MDCNFG_DE1
;add above
and also changed some uart address in platform.reg
such as:
;-------------------------------------------------------------
; Serial1 : FFUART
;-------------------------------------------------------------
; @CESYSGEN IF CE_MODULES_SERIAL
IF BSP_NOSERIAL !
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\Serial]
"Dll"="xsc1bd_serial.Dll"
; "IoBase"=dword:a6300000 ;FFUART_BASE_U_VIRTUAL
"IoBase"=dword:a8300000 ;FFUART_BASE_U_VIRTUAL
................
///////////////////////////////////////////////
when all of them had done,I download the NK.bin,
and the debug information shows:
rom_offset=0x0.
Found pTOC signature.
ROMHDR at Address 800B8044h
RomHdr.ulRAMStart=81C50000h RomHdr.physfirst=800B8000h.
Done.
Writing 0x80076BD8 to flash address 0xB8340000 (length=0xA40).
Sector=0x200 (Length=0x6) Block=0x1 (Length=0x1).
Handling non-block aligned data...
FlashErase: Unlocking flash block(s) [0x1, 0x1] (please wait): Done.
Erasing flash block(s) [0x1, 0x1] (please wait): .Done.
Writing to flash (please wait): Done.
Got EDBG_CMD_JUMPIMG
Got EDBG_CMD_CONFIG, flags:0x00000000
Download successful! Jumping to image at physical 0xA00B9000...
Begin
******************************************************
******************************************************
******************************************************
******************************************************
******************************************************
OEMInitDebugSerial using UART2
Windows CE Kernel for ARM Built on Mar 13 2003 at 22:54:19
ProcessorType=02d0 Revision=6
sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800 OEMAddressTable =
800b9ef4
as u see,my system hung at last,
if normal,sp=ffffc7cc should be printed behind
OEMAddressTable = 800b9ef4
but now,system hung there....
and Platform builder printed the word"Kernel debugger is waiting to
connect with target."
Anybody has experience ?
could u give me some advice?
I so appreciate it, thank u a lot.
.
- References:
- sdram configuration,pls help
- From: blueYork
- sdram configuration,pls help
- Prev by Date: Re: Removing Hardware from System by UserMode Code and Reinstalling it...
- Next by Date: Re: IoAllocateMdl Failure- returns NULL 30% in Vista64 but not in othe
- Previous by thread: sdram configuration,pls help
- Next by thread: IOCTL_VOLUME_ONLINE and IOCTL_VOLUME_OFFLINE
- Index(es):
Relevant Pages
|
