Re: Help! RAS and 2 NICs?
From: Tyler (anonymous_at_discussions.microsoft.com)
Date: 03/04/04
- Next message: Tyler: "Re: Help! RAS and 2 NICs?"
- Previous message: Henry Craven: "Re: Personal replies to people in this group."
- In reply to: Marina Roos [SBS-MVP]: "Re: Help! RAS and 2 NICs?"
- Next in thread: Tyler: "Re: Help! RAS and 2 NICs?"
- Messages sorted by: [ date ] [ thread ]
Date: Wed, 3 Mar 2004 17:03:56 -0800
Well the 209 # is all internal IPs.. I really dont want to
change my entire setup for a specific IP.. My outside IP
is a static IP.. I purchased a block of 5.. If you are
saying that my external NIC should be a 10# how will this
affect my Mail server and my web server? The 67.40.86.110
is to my router which from there it goes out.. the
67.40.86.105 is the 1st static IP in my block.. This
serves as an Exchange server and a WebServer.. This worked
before.. Why would running the RAS wizard change anything?
The 209.180.158.1 Is a static IP on my server (an IP I
assigned just because, no reason for this IP) This should
have no effect on the outside connection because this IP
see's no outside connection.. The 67.40.86.105 is also a
static IP that was purchased through my ISP..
Maybe I am not explaining this correctly, this setup has
worked now for about 2 years.. Now that I need to setup a
VPN and run an outside connection to my server over the
internet, I ran the RAS wizard and now this setup doesnt
want to work.. Even if I changed my IPs to private ranges
it still doesnt make any sense as to why it stopped
working.. How would changing IPs to a private range have
any affect? This is kicking my ass, I am going to try an
uninstall of the 2nd NIC, let the system reinstall it and
see where I go from there..
>-----Original Message-----
>This is never going to work. Why are you using public
IP's on your nics?
>Better get the to the private ranges. Use static IP's on
the nics.
>Internal nic should be something like:
>IP: 192.168.16.2
>GW blank
>DNS 192.168.16.2
>
>External:
>IP: 10.0.0.2
>GW 10.0.0.3
>DNS 192.168.16.2
>
>
>--
>Regards,
>
>Marina
>Microsoft SBS-MVP
>
>"Tyler" <anonymous@discussions.microsoft.com> schreef in
bericht
>news:654c01c40150$00f84aa0$a501280a@phx.gbl...
>> Here it is I am not using copy & paste, so I am just
going
>> to type the IP info..
>>
>> LAN card
>>
>> Physical Add: 00-04-5a-58-e8-89
>> DHCP Enabled: No
>> IP Address: 67.40.86.106 (My static IP)
>> SubnetMask: 255.255.255.248
>> IP Address: 209.180.158.1
>> SubnetMask: 255.255.255.0
>> Gateway: 67.40.86.110
>> DNS and WINs are 209.180.158.1
>>
>> Net Card
>>
>> Physical Address: 00-04-5a-7e-9b-a6
>> DHCP Enabled: No
>> IP Address: 67.40.86.105
>> SubnetMask: 255.255.255.248
>> GateWay: 67.40.86.110
>> No DNS and No WINs
>>
>> Now my LAN Card is usually not setup with a Static IP
>> because it doesnt use the outside IPs.. Right now it is
so
>> I can have an outside connection.. This is how my cards
>> have been and then after I ran the RAS setup for a VPN
>> connection it seems like the two cards have stopped
>> communicating.. I reran the Connection MAnager so that I
>> can specify the inside card and the outside card.. I
>> recreated my LAT tables with the inside IPs.. I dont
know
>> what is going on.. I am not sure how the outside
>> connection stopped working from before the RAS setup to
>> after the RAS Setup.. I didnt change any of the
settings I
>> just ran it for an outside VPN connection.. I am not
sure
>> where to go next.. My statics start with the 67 and my
>> internals start with the 209.
>>
>>
>> >-----Original Message-----
>> >Can you post the ipconfig/all please?
>> >
>> >--
>> >Regards,
>> >
>> >Marina
>> >Microsoft SBS-MVP
>> >
>> >"Tyler" <anonymous@discussions.microsoft.com> schreef
in
>> bericht
>> >news:62ae01c4012a$578ab9a0$a501280a@phx.gbl...
>> >> I have an SBS setup with 2 NICS.. Everything working
>> just
>> >> fine.. Now I needed to setup RAS and after I set this
>> up,
>> >> my outside connection is gone.. I cannot get outside
my
>> >> network after I setup RAS, My network configuration
and
>> IP
>> >> addresses are the same, I run the Network management
>> tool
>> >> to specify the inside network and outside network
NICS,
>> >> Everything works just fine except that it seems like
the
>> >> inside NIC and the outside NIC dont communicate
>> anymore..
>> >> Now if I setup my outside line ips to double up with
the
>> >> internal NIC I have outside connection.. Can anyone
help
>> >> me out? Where to start? I have been working on this
for
>> a
>> >> full day now and I am stumped.. I disable my outside
NIC
>> >> becuase it isnt communicating to my inside NIC. I
have a
>> >> stack of 5 static IPs and if I setup the internal NIC
>> with
>> >> a 2nd IP (a static) and the static gateway, I have
>> >> internet connection.. If I enable the outside NIC and
>> take
>> >> my static IPs out of the internal NIC (so it actually
>> uses
>> >> the outside NIC for the outside connection) I lose
>> >> internet connect.. The only thing I havent done is
>> remove
>> >> the outside NIC from my hardware settings for it to
>> >> reload.. I really dont know why I would have to do
that
>> >> since everything was working just fine until I ran
the
>> RAS
>> >> setup wizard.. Does anyone have any ideas?
>> >
>> >
>> >.
>> >
>
>
>.
>
- Next message: Tyler: "Re: Help! RAS and 2 NICs?"
- Previous message: Henry Craven: "Re: Personal replies to people in this group."
- In reply to: Marina Roos [SBS-MVP]: "Re: Help! RAS and 2 NICs?"
- Next in thread: Tyler: "Re: Help! RAS and 2 NICs?"
- Messages sorted by: [ date ] [ thread ]
Relevant Pages
|
