Re: Help! RAS and 2 NICs?
From: Tyler (anonymous_at_discussions.microsoft.com)
Date: 03/03/04
- Next message: Thomas Kroljic: "Added New Disk to System"
- Previous message: BillP: "SBS2003 Public Access"
- In reply to: Marina Roos [SBS-MVP]: "Re: Help! RAS and 2 NICs?"
- Next in thread: Marina Roos [SBS-MVP]: "Re: Help! RAS and 2 NICs?"
- Reply: Marina Roos [SBS-MVP]: "Re: Help! RAS and 2 NICs?"
- Reply: SuperGumby: "Re: Help! RAS and 2 NICs?"
- Messages sorted by: [ date ] [ thread ]
Date: Wed, 3 Mar 2004 10:47:39 -0800
Here it is I am not using copy & paste, so I am just going
to type the IP info..
LAN card
Physical Add: 00-04-5a-58-e8-89
DHCP Enabled: No
IP Address: 67.40.86.106 (My static IP)
SubnetMask: 255.255.255.248
IP Address: 209.180.158.1
SubnetMask: 255.255.255.0
Gateway: 67.40.86.110
DNS and WINs are 209.180.158.1
Net Card
Physical Address: 00-04-5a-7e-9b-a6
DHCP Enabled: No
IP Address: 67.40.86.105
SubnetMask: 255.255.255.248
GateWay: 67.40.86.110
No DNS and No WINs
Now my LAN Card is usually not setup with a Static IP
because it doesnt use the outside IPs.. Right now it is so
I can have an outside connection.. This is how my cards
have been and then after I ran the RAS setup for a VPN
connection it seems like the two cards have stopped
communicating.. I reran the Connection MAnager so that I
can specify the inside card and the outside card.. I
recreated my LAT tables with the inside IPs.. I dont know
what is going on.. I am not sure how the outside
connection stopped working from before the RAS setup to
after the RAS Setup.. I didnt change any of the settings I
just ran it for an outside VPN connection.. I am not sure
where to go next.. My statics start with the 67 and my
internals start with the 209.
>-----Original Message-----
>Can you post the ipconfig/all please?
>
>--
>Regards,
>
>Marina
>Microsoft SBS-MVP
>
>"Tyler" <anonymous@discussions.microsoft.com> schreef in
bericht
>news:62ae01c4012a$578ab9a0$a501280a@phx.gbl...
>> I have an SBS setup with 2 NICS.. Everything working
just
>> fine.. Now I needed to setup RAS and after I set this
up,
>> my outside connection is gone.. I cannot get outside my
>> network after I setup RAS, My network configuration and
IP
>> addresses are the same, I run the Network management
tool
>> to specify the inside network and outside network NICS,
>> Everything works just fine except that it seems like the
>> inside NIC and the outside NIC dont communicate
anymore..
>> Now if I setup my outside line ips to double up with the
>> internal NIC I have outside connection.. Can anyone help
>> me out? Where to start? I have been working on this for
a
>> full day now and I am stumped.. I disable my outside NIC
>> becuase it isnt communicating to my inside NIC. I have a
>> stack of 5 static IPs and if I setup the internal NIC
with
>> a 2nd IP (a static) and the static gateway, I have
>> internet connection.. If I enable the outside NIC and
take
>> my static IPs out of the internal NIC (so it actually
uses
>> the outside NIC for the outside connection) I lose
>> internet connect.. The only thing I havent done is
remove
>> the outside NIC from my hardware settings for it to
>> reload.. I really dont know why I would have to do that
>> since everything was working just fine until I ran the
RAS
>> setup wizard.. Does anyone have any ideas?
>
>
>.
>
- Next message: Thomas Kroljic: "Added New Disk to System"
- Previous message: BillP: "SBS2003 Public Access"
- In reply to: Marina Roos [SBS-MVP]: "Re: Help! RAS and 2 NICs?"
- Next in thread: Marina Roos [SBS-MVP]: "Re: Help! RAS and 2 NICs?"
- Reply: Marina Roos [SBS-MVP]: "Re: Help! RAS and 2 NICs?"
- Reply: SuperGumby: "Re: Help! RAS and 2 NICs?"
- Messages sorted by: [ date ] [ thread ]
Relevant Pages
|
